Ghost Immobiliser Fitter
Ghost immobilisers are one of the most effective ways to safeguard your vehicle from thieves. They prevent vehicles from being started until the correct code is entered. They can be used to track vehicles remotely. These systems are becoming increasingly popular, and a lot of insurance companies give discounts to drivers who have installed them.
It is tamper proof.
The Ghost Immobiliser is a sophisticated security device, blocks your car from beginning without a unique PIN or beacon. The system can be modified to fit your vehicle and is highly effective as an anti-theft solution. It is essential to test your system following installation to make sure it's functioning properly. By entering the PIN when you start the engine is a straightforward way to test that the system has been installed correctly. Regular testing will help identify any problems or issues with the system early.
The system communicates directly with the ECU and will not allow your vehicle to start unless you select the proper sequence. This can be accomplished using the electronic buttons on the steering wheel, or via an app for smartphones. Its tamper-proof design and low profile make it difficult for thieves to locate or remove. It can also be used with beacons to monitor the location of your vehicle. It is a great solution to protect valuable vehicles that have been modified or for people who want to protect their expensive or valuable automobiles.
This tamper-proof device uses the buttons on your steering wheel to create an exclusive sequence that only you know. The sequence is mathematically impossible for thieves to guess, and can be easily changed with a secure reset key. It can be installed in most automobiles and is simple to install with the aid of an expert.
After installing the device you will need to connect it to a power source as well as a grounding point. To identify the wires that are required, you will need to obtain the wiring diagram of your vehicle. Be ghost immobiliser tracker to insulate the connections with heat shrink tubing, or insulation tape to avoid short circuits and electrical damage. You should also check the connections and mounting for any signs of tampering caused by thieves.
Ghost 2 can be set up in Service/Valet mode for older vehicles which require battery isolation during servicing or maintenance. This will turn off the device using an individual pin code, which will prevent it from being turned back on by thieves.
Wireless
Contrary to other anti-theft gadgets, ghost immobilisers operate in a quiet manner and aren't recognized by thieves. They can be fitted in various vehicles and protect them from hacking, key cloning, and signal relay attacks. They also connect to the CAN network and can be used to track vehicles remotely. They can also notify owners immediately if their car is stolen. Certain insurance companies offer discounts to customers who purchase them. It is the most effective way to avoid car theft.
The Ghost II immobiliser offers a simple and affordable way to safeguard your vehicle from theft. This discrete device operates wirelessly and is compatible with all vehicles. It is weatherproof, tamperproof and is compatible with any vehicle. It comes with a 3-year guarantee. Contrary to other security products that are available, Ghost II is not a security device that Ghost II does not require any additional wiring or components. The unique pin-code sequence safeguards against key cloning and theft by preventing your vehicle from starting until a special sequence of disarming is entered. The sequence can range between one and twenty buttons, which means that thieves would need to spend more time trying to hacking.
The Ghost II can also block signals from a thief’s key fob. It can determine the moment a key fob has been duplicated or stolen and shut down the engine by setting off an alarm. It also can stop the use of a signal relay device, which is frequently used by organized car-thief gangs to gain access to vehicles.
It is essential to regularly test the Ghost Immobiliser to make sure that it's functioning as intended. This will help you identify any issues early and fix them before they become a significant problem. It is a good idea to test the system by entering the PIN code and starting the engine as part of your regular vehicle inspections.
It is essential that the immobiliser is mounted in a place that is difficult to access by thieves. If you can, place the unit behind your dash using cable tie. Be sure that all connections are properly insulated and cannot be altered by thieves. Double-check that the mounting location is secured.
It can be used with a wide range of vehicles.
The ghost immobiliser is an efficient security device that will aid in preventing car theft. It works by blocking your vehicle's engine from starting until the proper pin code is entered. This code can be created by pressing a sequence of buttons already present on your steering wheel, door panel or central console. The immobiliser is secure and is reprogrammable by the owner at anytime. It also shields against hacking, key-cloning and other malicious activities.
While some drivers might attempt to install the Ghost Immobiliser on their own however, it is recommended you hire an expert. This is because the installation process is complex and any errors could cause the device to be ineffective or even harm your vehicle. In addition, DIY installation could void warranties for both the Ghost Immobiliser as well as your vehicle.
A good place to start is to get the wiring diagram of your vehicle model. This will provide you with a guide to locate the CAN H wires and CANL wires that are used for the immobiliser. Once you have identified these wires mark them to ensure that they are not accidentally disconnected during the installation process. Select a safe and reliable grounding point.
After the wires have been connected, it's a good idea to test the immobiliser to make sure that everything is functioning properly. Enter the PIN code, then start your engine to see whether everything works. It is recommended to test the immobiliser regularly to ensure it is working as it was intended.
The ghost immobiliser is unique in that it doesn't require keyfobs or LED indicators. It is able to be deactivated with a specific sequence on your steering, door panel or centre console. The immobiliser is also tamper-proof, and does not leave any trace of installation behind which makes it difficult for thieves to locate or disable. It can also be used to strengthen the security of your vehicle in the event of an attack. Many insurance companies recommend it.
Easy to install
The Ghost immobiliser is a highly sophisticated device that helps keep your vehicle secure from the most skilled thieves. It stops the car from starting unless the unique PIN code or sequence is entered along the key fob. This prevents cloning or hacking or even theft of keys. Thieves cannot steal your car. It also makes use of a variety of other sensors to detect attempts to drive away and notify the owner or the police in case of any tampering.
Installing a ghost-immobiliser can be tricky, especially for people without prior experience installing alarms or other security systems. It is crucial to have the right tools and materials for a successful installation. A multimeter can be used to verify electrical values, and insulation tape and cable ties can help protect connections. The Ghost immobiliser user manual provides specific instructions tailored to the model and wiring of your vehicle.
It is essential to verify the wire locations for the CAN H and L before the installation to ensure precision. They are vital for powering the immobiliser which is why mistakes could lead to malfunctions or system failures. Mark the wires using labels or tape so you can track them. You should also identify an uninterrupted source of 12V and a grounding.
Once you've found the right location, it's time to start assembling the ghost immobiliser. To avoid short circuits or accidental airbag deployment, you will have to disconnect your battery first. You can then begin connecting the wires. Be sure to follow the instructions in the user's guide to ensure a safe and secure installation.
After you've completed the wiring After you have completed the wiring, connect the Ghost immobiliser via CAN to the engine control unit. It will be a challenge for thieves, since the device is directly connected to the engine control unit, and it is not possible to remove or disable it. It's also tamper-proof and the only method to disable it is by entering a personal pin code. The pin code will only be accessed by the owner of the vehicle and installer.
You can also make use of the Ghost immobiliser to temporarily allow another person to drive your car for a short period in the event that you're away for work or require an emergency service. This feature is known as Service/Valet mode, and you can activate it by using an app for mobile devices or the key fob.